鉛防護鉛門外形美觀，不銹鋼板與板連接采用電梯不銹鋼板接口技術，而且全部采用進口膠粘接，粘接非常平整、牢固、不脫膠;主結構采用獨特設計，使門與墻壁縫隙劑量泄漏相當小;具有紅外線防夾人裝置，保證工作人員的人身;另外還具有防三相電源反相損壞屏蔽門開門電機裝置，保證在三相電源反相時能立即知道電源反相。
Lead protection lead door has beautiful appearance, stainless steel plate and plate connection adopts elevator stainless steel plate interface technology, and all adopt imported glue bonding, bonding is very flat, firm, no degumming; the main structure adopts unique design, so that the dose leakage between the door and the wall is quite small; it has the anti pinch device of red external line to ensure the personal safety of the staff; In addition, it also has a device to prevent the three-phase power supply from damaging the opening motor of the screen door, so as to ensure that the reverse phase of the power supply can be immediately known when the three-phase power supply is reversed.
防射線鉛門主要用于需阻擋射線通過的進出口，主要使用于醫院、機房和礦區中。按門型可分為平開防射線鉛門、推拉防射線門和電動防射線鉛門。
The ray proof lead door is mainly used in the import and export where the ray needs to be blocked. It is mainly used in hospitals, computer rooms and mining areas. According to the door type, it can be divided into horizontal opening ray proof lead door, push-pull ray proof door and electric ray proof lead door.
1.平開鉛門 ;平開鉛門，可分為內開門和外開門，門體的結構和材料是根據放射線機的功率大小(KV)及門洞口大小來決定的，五金件為進口專用件。
1. The lead door can be divided into the inner door and the outer door. The structure and material of the door body are determined by the power (kV) of the radiation machine and the size of the door opening, and the hardware parts are imported special parts.
2.推拉鉛門 ;推拉防射線門，開啟方向是沿著墻壁平行移動，門體的結構與材料是根據放射線機的功率大小(KV)及門洞口大小來決定的，門框結構與平開門結構有所區別。
2. Push and pull lead door; push and pull ray proof door, the opening direction is parallel to the wall. The structure and material of the door body are determined by the power of the radiation machine (kV) and the size of the door opening. The door frame structure is different from the side door structure.
3.電動鉛門 ;電動防射線門一般適合較大的門體，由于重量較重，人力開啟比較吃力，所以采用電動開啟方式。
3. Electric lead door; electric ray proof door is generally suitable for larger door body. Due to its heavy weight and hard manual opening, electric opening mode is adopted.
開啟形式可分為平開式和平移式。：
Open form can be divided into flat open type and moving type. :
1 、應定期對工業門上的灰塵進行清洗，保持工業門及玻璃、五金件的清潔和光亮。因為即使是不銹鋼，一旦沾染上灰塵、污垢，其中的化學物質也會腐蝕不銹鋼表面，長此以往的話，會使鋼體變壞、變爛，影響輻射防護自動門的運行性能。
1. The dust on the industrial door should be cleaned regularly to keep the industrial door, glass and hardware clean and bright. Because even stainless steel, once contaminated with dust and dirt, the chemical substances in it will corrode the surface of stainless steel. In the long run, the steel body will be deteriorated and rotten, which will affect the operation performance of radiation protection automatic door.
2 、一旦輻射防護自動門上污染了油漬等難以清洗的東西，可以用潔爾亮擦洗，而更好不要用強酸或強堿溶液進行清洗，這樣不僅容易使型材表面光潔度受損，也會破壞五金件表面的保護膜和氧化層而引起五金件的銹蝕，特別是有些客戶在用硫酸清洗墻面時，千萬注意不要讓門窗受染。
Two Once the radiation protection automatic door is contaminated with oil stains and other things that are difficult to clean, you can use jieerliang to clean, but it is better not to use strong acid or alkali solution for cleaning. This will not only easily damage the surface finish of the profile, but also damage the protective film and oxide layer on the surface of the hardware, causing corrosion of the hardware parts. Especially, some customers should pay attention to this when cleaning the wall with sulfuric acid Don't let the doors and windows get stained.
3 、應及時清理框內側顆粒狀等雜物，以免其堵塞排水通道而引起排水不暢和漏水現象，后果嚴重的還會影響輻射防護自動門的運行，縮短自動門的使作壽命，并且還存在隱患。
3. It is necessary to clean up the particles and other impurities inside the frame in time, so as to avoid blocking the drainage channel and causing poor drainage and water leakage. If the consequences are serious, the operation of the radiation protection automatic door will be affected, the service life of the automatic door will be shortened, and there will be potential safety hazards.
4 、在開啟工業門時，力度要適中，盡量保持開啟和關閉時速度均勻。
4. When opening the industrial door, the force should be moderate and the speed of opening and closing should be uniform as far as possible.
5 、平時在進出自動門時，忌諱急躁、橫沖直撞，盡量避免堅硬的物體撞擊輻射防護自動門或劃傷型材表面。
5. When entering and leaving the automatic door, avoid impatience and collision, and try to avoid hard objects impacting the radiation protection automatic door or scratching the surface of profile.
6 、在發現工業門在使用過程中有開啟不靈活或其它異常情況時，應及時查找原因，如果客戶自已不能排除故障時，應及時與輻射防護自動門生產廠家或供應商聯系，以便故障能得到及時排除。如果自動門沒有得到及時維修，應暫停使用，以免產生意外。
6. In case of inflexible opening or other abnormal conditions found in the process of using the industrial door, the cause shall be found out in time. If the customer can not eliminate the fault by himself, the manufacturer or supplier of automatic radiation protection door shall be contacted in time, so as to eliminate the fault in time. If the automatic door is not repaired in time, it should be suspended to avoid accidents.
This article is organized and released by radiation protection equipment. Do you have any understanding of these contents? For more information, please click: http://m.tiaoi.com.cn We'll have a lot more to see.
18678809986
