1. Check the boiler appearance and gas pressure - when preparing to start up the gas-fired boiler, the stoker on duty should first do a comprehensive inspection, including the appearance of the boiler, valves and various connecting parts, and then check the gas pressure to ensure that the pressure value is within the normal range rather than too high or too low. After the inspection and confirmation, the gas supply can be opened Give the valve.

2、檢查供水系統-燃?xì)忮仩t在燃燒的時候里面是要有水的，否則就會發生危險。所以，在啟爐之前司爐工人應該檢查供水系統，看水泵能不能上水，如果不能正常上水就要將放氣閥打開放氣，知道水泵能夠開始上水為止，然后再打開供水系統中的各個閥門。

2. Check the water supply system - the gas-fired boiler should have water when it is burning, otherwise it will cause danger. Therefore, before starting the boiler, the stoker should check the water supply system to see if the water pump can supply water. If the water can not be supplied normally, the air release valve should be opened to vent until the water pump can start to fill water, and then open the valves in the water supply system.

3、檢查水位-如果燃?xì)忮仩t里面的水太多或太少都會對鍋爐的運行造成影響，在啟爐之前做好水位計的檢查非常重要，因?yàn)樗挥?jì)的作用就是為了讓司爐工能夠隨時了解目前鍋爐里面還有多少水。

3. Check water level - if there is too much or too little water in the gas-fired boiler, it will affect the safe operation of the boiler. It is very important to check the water level gauge before starting the boiler, because the function of the water level gauge is to let the fireman know how much water there is in the boiler at any time.

所以，燃?xì)忮仩t啟動前要看水位計的位置是否正常，而且還要看水位計的計位器和水位色塞是否處于打開的位置，以免出現假水位的現象，然后觀察是否缺水。能夠滿足客戶的燃?xì)忮仩t廠家告訴大家，以上就是燃?xì)忮仩t在啟爐之前需要檢查的事項，除了這些之外，司爐工人還要檢查煙道上的擋風板并確保全部處于打開的狀態。只有將鍋爐的各個方面都認真檢查好才能正式開始啟動燃?xì)忮仩t。

Therefore, before the start-up of the gas-fired boiler, it is necessary to check whether the position of the water level gauge is normal, and whether the level indicator and water level color plug are in the open position, so as to avoid the phenomenon of false water level, and then observe whether there is water shortage. The gas-fired boiler manufacturers who can meet the customers tell us that the above are the items that need to be checked before starting the gas boiler. In addition to these, the firemen should also check the wind deflector on the flue and ensure that they are all in the open state. Only by carefully checking all aspects of the boiler can the gas-fired boiler be officially started.