多介質過濾請經過一段時的運行之后,就要對其進行清洗,下面山東多介質過濾器廠家就給大家詳細講解一下清洗步驟!
After a period of operation, the multi-media filter must be cleaned. The following Shandong multi-media filter manufacturer will give you a detailed explanation of the cleaning steps!
1、放水
1. Drainage
開啟多介質過濾器排氣門、反洗排水門、正洗排水門,放水水位高出濾料20--40cm,關閉正洗排水門。(大約5分鐘)
Open multi-media filter exhaust valve, backwash drainage door and forward wash drainage door, drain water until the water level is 20-40 cm higher than the filter material, and close the front wash drainage door. (About 5 minutes)
2、空氣擦洗
2. Air scrubbing
開啟多介質過濾器進風門,啟動羅茨風機,對濾料擦洗5min,停羅茨風機,關閉進風門。
Open the multi-media filter intake door, start the Roots blower, scrub the filter material for 5 minutes, stop the Roots blower, close the intake door.
空擦中反洗排水管不應有大量水排出,容易跑濾料。若出現大量排水說明過濾器內部水位過高,立即停止空擦,繼續放水。
The backwashing drain pipe should not discharge a large amount of water during air scrubbing, so it is easy to run off the filter material. If there is a large amount of drainage indicating that the water level inside the filter is too high, immediately stop empty wiping and continue to drain water.

3、反洗
3. Backwashing
開啟多介質過濾器反洗進水門,啟動清洗水泵,用進水手動門控制流量100--130m3/h,控制濾料膨脹高度不超過上監視窗中部,檢查反洗排水無濾料,反洗排水清。
Open the multi-media filter backwash inlet door, start the cleaning pump, use the manual inlet door to control the flow rate of 100-130 m3/h, control the expansion height of the filter material not to exceed the middle of the upper monitoring window, check the backwash drainage without filter material, until the backwash drainage is clear.
4、上水
4. Upper Water
關閉反洗排水門,待排氣門滿水,停清洗水泵。關閉反洗進水門、反洗排水門、排氣門,多介質過濾器清洗合格備用。
Close the backwash drain door until the exhaust valve is full of water. Stop cleaning the pump. Close the backwash inlet valve, backwash drain valve and exhaust valve, and clean the qualified backup filter with multi-media.
Thank you for your reading. If there is anything wrong, welcome to our official website: http://m.tiaoi.com.cn. Leave us a message and comment. We will give you a satisfactory answer!